Image Added

Flash Settings 8-Speed

xHP features a “Customization Module”, which allows users to change certain has “Flash Settings”, allowing the user to change specific settings before flashing an OTS or Custom - Map. The Module This injects those these user-defined values into every Map before flash. Usage each map before it is flashed.

Use is simple: Just do your settings, save them and

• adjust the desired settings

• save the settings

• flash any map to apply

• the settings.

Custom Launch Control 8-Speed

Launch Control is a 2-Step process. It gets activated only in S/Sport+ or S/Traction mode of your vehicle. Place your car on a safe, level and straight street. Move your Gear Lever to S and put the car into Traction or Sport+ mode. Now press the brake VERY hard and quickly apply full throttle with the kickdown switch depressed. On vehicles with LC from factory you will see "Launch Control active" on your dash. The amount of boost/torque your car is allowed to build while the brake is depressed is setup with the "Set Launch Torque" slider. After releasing the brake, the Car tries to manage torque and traction along programmed presets which can be tuned up and down with the "Torque Scaling After Launch" slider. 0% is the factory setting and is optimized for stock cars. Tuned cars may need different settings. You are free to experiment with those settings and find your personal best.

Drag Race Mode

Drag Race Mode is designed to extract the absolute maximum from your transmission and boost your 0-60 and 60-120 times! Torque Reduction during shifts is completely disabled, shift pressures are maxed out and clutch protection thresholds are raised so you can put the full power of your engine to the ground, no matter what happens.

Omitting torque reduction during shifts, will lead to better acceleration times. This is especially true on turbo-charged cars, as the engine does not need to cut boost during overlap phase of the transmission. To match the additional load on the clutch packs, shifts will be carried out with maximum possible pressure. Stock safety thresholds for clutch-load are raised accordingly. The 8-Speed transmissions employ a similar logic during Launch Control operation but Drag Race Mode takes this idea even a bit further. Also Launch Control mode will be internally disabled on some cars after a certain counter has been reached. Drag Race mode will inhibit the LC counter and will be available permanent.

Drag Race Mode will automatically enable in Launch Control mode and in Sport+/DSC OFF mode (8-Speed) or in Manual mode (6-Speed). The raised pressures will get noticeable only above approx. 40% throttle. Normal daily driving in Comfort/D is unaffected. However, please keep in mind that this is a true performance function and should not be used permancently. Usually all of our Stages are developed withing the limits of the transmission, to ensure unaffected longevity and stock-like trouble free operation.

Drag Mode intentionally ignores such limits in favor of maximum performance and should therefore only be used in special situations, e.g. competing on the Drag-Strip! Drag Mode can be applied to any of the Stages or even to your Stock file.

Shiftmap Editor with Presets

The shift map editor enables you to change all shift points in D and S mode to your personal liking. For instance you can make your car shift later from 1st to 2nd Gear when accelerating, or vice versa. Or make it hold 8th Gear for longer on the Highway when accelerating. For an easy start, xHP offers 4 presets: Relaxed, Relaxed+, Sportive and Sportive+.

Those presets make it easy to do a quick test on your car and experience the changes. Just select a preset and flash any map again. xHP will automatically apply the Presets to your Shiftmap during the Flash. Presets work with your Stock Calibration, with all OTS Maps and with Custom Files flashed.

Relaxed and Relaxed+: Your car will shift earlier up and will be less eager to downshift when pressing the throttle.

Sportive and Sportive+: Your car will shift up later and will stay for longer in lower gears. It will also react more quickly to throttle inputs and will be more happy to shift down.

Shiftmap Editor: Setup hints

The shift map editor enables you to change all shift points in D and S mode to your personal likings. A “shift map” consists of 14 lines, which are spread over throttle input.
Up- and downshifts can be independently configured. The setting made in the editor are always relative to the flashed map. You do not set exact shift points, but rather are able to change the shifting of a given OTS or custom map! The spread is from +50% to - 50% for each shift. For example, if your 5-6 shift on low loads normally occurs at 50 mph, but you want it not to happen before 55 mph, pull the 5->6 slider to + 10%. Same goes for the downshifts. If your trans normally downshifts on 40 mph from 6->5 during coasting, but you want that to happen at 50 mph, pull the slider for 6->5 up to +25%.

Be sure to make sensible changes. If you alter the 1-2 shift upwards, you should do the same gradually to the subsequent shifts, to get a “natural” shift-feel during driving. Rule of thumb is to make bigger changes on the lower gears, and smaller changes on the upper gears. However, you are free to experiment with these settings. xHP pre-calculates and validates all changes against every OTS Map stored on the device. A fixed ruleset gets applied to auto-correct "wrong" settings and prevent dead-locks. Such a dead-lock could happen if your 2-3 upshift-point would be set below the 3-2 downshift-point, or if an upshift would lead to a target RPM below idle- speed of the engine.

Below is an example how to turn the standard Stage-3 Map of a 335i in D-Mode into a very comfortably and low shifting Map:

“Drag Race Mode” is designed to squeeze the absolute maximum out of your transmission and improve your 0-60 and 60-120 times! Torque reduction during shifts is entirely disabled, shift pressures are maxed out, and clutch protection thresholds are raised so you can put the full power of your engine to the ground no matter what.

The absence of torque reduction during shifting results in better acceleration times. This is especially true on turbocharged cars, as the engine does not have to reduce boost during the overlap phase of the transmission. To compensate for the additional load on the clutch packs, shifts are made with the maximum possible pressure. The standard safety thresholds for clutch load are increased accordingly.

The 8-speed transmissions use a similar logic in Launch Control mode, but Drag Race mode furthers this idea. Launch Control mode is also internally disabled on some cars after reaching a specific counter. In Drag Race mode, the LC counter is disabled and is permanently available.

Drag Race mode is automatically activated in Launch Control mode and Sport+/DSC OFF mode (8-speed) or Manual mode (6-speed). The increased pressure only becomes noticeable above about 40% throttle. Everyday daily driving in Comfort/D is unaffected.

All our stages are typically developed within the transmission limits to ensure unaffected longevity and stock-like trouble-free operation.

Drag Mode deliberately ignores these limits for maximum performance and should only be used in particular situations, such as drag strip competition! Drag Mode can be applied to any of the stages or even to your stock file.

Launch Control is a 2-step process. It is only activated when your car is in S/Sport+ or S/Traction mode.

• Stop your car in a safe, and make sure it is a level and straight road.

• Move your gear lever to S and put the car in Traction or Sport+ mode.

• Now apply the brake VERY firmly and quickly apply full throttle with the kick-down switch depressed. On cars with LC from the factory, you will see "Launch Control active" on your dashboard.
  The amount of boost/torque your car can build up while the brake is depressed is set with the "Set Launch Torque" slider.

• Release the brakes to launch your car.
  After releasing the brake, the car will attempt to manage torque and traction according to programmed presets, which can be adjusted up and down with the "Torque Scaling After Launch" slider.

0% is the factory setting, optimised for stock cars. Tuned cars may require different settings.

Feel free to experiment with these settings to find your personal best.

Override Brake Boost Protection

The ZF6HP and ZF8HP use a torque converter to amplify the torque coming from the engine before it enters the rest of the driveline. This amplification must be considered while brake boosting to protect the transmission and the rest of the driveline.

The typical torque multiplication factor for ZF torque converters during brake boosting is around 1.75 - 1.9. (Engine speed > 800 rpm and turbine speed: 0 rpm).

This makes torque converters great for launching vehicles, but due to the amplification, the allowable torque from the engine needs to be limited. This limit is independent of any other torque limits and is only applied during the boost phase of the converter.

It is hard-coded per transmission variant (6HP21, 6HP28, 8HP45, 8HP50, 8HP75, etc.) and cannot usually be changed by the calibration engineer. There is a good reason for this: even small changes result in substantial torque jumps after the converter.

The override function in xHP has five settings from 5% to 15% to increase the allowable torque, OR you can turn the protection off completely. If OFF is selected, the engine torque is not limited by this particular function but only by the corresponding gear limiter. (Gear 1 or Gear 2)

All 8HP transmissions share a 1st Gear with a very short ratio. Particularly on higher-powered cars, staying in second gear at a standstill adds to the comfort of everyday driving (you save one gear change at each junction). It can even help optimise 0-60 times on high-powered RWD cars with limited traction.
xHP lets you choose whether to activate this function for D, S, or both modes.

There is no downside regarding wear, as torque converters transmit torque through fluid rather than friction plates (as in a manual or dual-clutch transmission).

The transmission reverts to standard behaviour when necessary, for example, in the following situations:

• When activated for D mode only, the transmission will revert to 1st gear when shifting to S and/or setting Sport or Sport+ with the DEC switch.

• In D/Comfort mode, the transmission immediately returns to 1st gear when Kickdown is activated. (emergency function)

• On a cold start (some cars)

• On a gradient or with a trailer attached

• When the transmission is overheated

Line pressure" is the main pressure at which the transmission operates outside of gear changes.
The primary input for calculating the line pressure is the torque value sent by the car's engine computer (ECU, DME).
The pressure is regulated by an electronic valve controlled by the TCU (Transmission Computer).
ZF transmissions typically operate with a maximum oil pressure of 16-20 bar. The higher the pressure, the higher the clamping force of the clutches and the higher the maximum torque that can be transmitted through the clutch pack before it starts to slip and quickly burns out.
This custom option adjusts the transmission mapping to allow about 5 to 15% more peak pressure.
Typically, ZF transmissions can easily handle the typical torque increase of Stage 1 or 2 engine tune when fitted with an xHP OTS map. However, for very high power increases, this option can make the difference between whether your clutch pack can cope.

Decoupling at a standstill is a comfort and fuel economy feature that minimises vibration at a standstill and reduces fuel consumption.

This function is active when a gear is engaged at a standstill. Through the torque converter, automatic transmissions create a constant power flow to the wheels when a gear is engaged. This means that the engine must overcome the torque converter's oil pressure when idling.

Decoupling cuts off the power flow after the torque converter by opening a clutch inside the transmission. This allows the engine to idle freely with minimal vibration and low fuel consumption. When the brake is released, the clutch automatically closes to reconnect the power flow.

In comfortable cars, this process is often perceived as a slight delay when moving off. In older/higher mileage cars, the opening/closing of the clutch is sometimes perceived as a slight jolt in the driveline. This function can be used to disengage the clutch at a standstill permanently.

This function sets your transmission to ECO mode without the sluggish throttle response usually associated with ECO-Pro mode. This makes saving fuel easier and more comfortable than the factory ECO-Pro mode.
Depending on your driving environment and habits, this function can save up to 0.5 l/100km.
The function is only active in D-Comfort. Other driving modes (D-Sport, S-Sport, manual, etc.) are unaffected.

Sailing (known as 'coasting') allows the car to disengage from gear and idle the engine when the driver releases the accelerator.
Mild-hybrid models switch off the engine during sailing/coasting, depending on the current traffic situation and/or driving style. The car automatically decides when to use coasting.

Use this custom setting to override and completely suppress 'Sailing/Coasting'. It is particularly useful on newer mild hybrid models, which no longer have a dedicated button for suppressing coasting.

The Stop-Go function makes the transmission stay in 2nd Gear at a standstill when a traffic jam situation is recognized. It's a comfort function to avoid continuous cycling between 1st and 2nd Gear in "Stop-Go" situations. Users can choose to turn this function ON or turn it OFF completely.

When a traffic jam is detected, the Stop-Go function keeps the transmission in 2nd gear. It's a comfort function to avoid constant shifting between 1st and 2nd gear in stop-go situations. The user can choose whether to enable or disable this function.

Most BMWs turn off their engines when they come to a complete stop in "Comfort Mode".
Use this custom feature to disable the start/stop function completely so the engine no longer turns off when coming to a stop.

Normally BMW cars are mapped to use higher shift points in Cruise mode when S or Sport/Sport+ is selected.
This custom option disables this behaviour on most vehicles. There are different ways of calculating shift points during “Cruise Mode”, so this option may not work on all cars.

The shiftmap editor allows you to change all shift points in D- and S-mode to suit your personal preferences. For example, you can make your car shift later from 1st to 2nd gear when accelerating, or vice versa. Or keep the car in 6th gear longer when accelerating on the motorway.
For an easy start, xHP offers four presets: Relaxed, Relaxed+, Sport and Sport+.

These presets make it easy to test your car and experience the changes quickly. Select a preset and flash any map again. xHP will automatically apply the presets to your shiftmap during the flash. Presets work with your stock calibration and all OTS maps and custom files that are flashed.

Relaxed and Relaxed+: Your car shifts up earlier and is less eager to downshift when you press the accelerator.

Sportive and Sportive+: Your car shifts up later and stays in lower gears longer. It responds more quickly to throttle inputs and is more willing to shift down.

Shiftmap Editor: Editing Presets

For further customisation, you can edit any presets and save your changes in up to three custom slots. Select a preset from the drop-down list and click the toolbox icon.

This will load the preset into the editor and reveal its saved settings. You can edit each up- and downshift and then save your changes to one of the three custom slots.

The presets themselves remain untouched, so you can always return to them. Your Custom Slots are also exported when you use the Import/Export feature, so you can easily share them with other users!

Shiftmap Editor: Setup hints

The shiftmap Editor allows you to change all shift points in D- and S-mode to your personal preference. A "shiftmap" comprises 14 lines spread across the throttle input.
The upshifts and downshifts can be configured independently. The settings made in the editor are always relative to the flashed map. You do not set exact shift points, but you can change the shifting of a given OTS or custom map! The range is from +50% to -50% for each shift.

Make sure you make sensible changes. If you change 1-2 up, you should do the same gradually with the subsequent shifts to get a 'natural' shift feel while driving. A good rule of thumb is to make larger changes in the lower gears and smaller changes in the higher gears.

However, you are free to experiment with these settings. xHP pre-calculates and validates all changes against each OTS map stored on the unit. A fixed set of rules is applied to correct 'wrong' settings and prevent deadlocks automatically. Such a deadlock could occur if your 2-3 upshift point were set below the 3-2 downshift point or if an upshift resulted in a target RPM below engine idle.

Below is an example of how the standard Stage 3 map of a 335i in D-mode can be turned into a very comfortable and low-shifting map:

This is just an example, but users are encouraged to experiment and find their own personal best shiftmap. The Shiftmap Editor allows you to change the character of a given map quite significantly by moving a few sliders.

This option will always keep the stock shift points, no matter which maps you flash.
With this feature enabled, changes in the shiftmap Editor will be relative to the stock shiftmaps, not the shiftmaps of any OTS map you may have flashed!

This function allows you to adjust how much torque reduction the transmission requests from the engine during upshifts. Just as in a manual gearbox, where the driver presses the clutch while releasing the accelerator, the automatic transmission requests the engine to reduce torque as it shifts from one gear to another.

Lowering the amount of torque reduction (slider to -) can reduce turbo lag after shifts, especially in the lower gears. Conversely, raising the amount of torque reduction (slider to +) can produce faster/sharper shifts.

The primary purpose of this function is to fine-tune your shifts to your current engine setup, as any aftermarket component or tuning will slightly alter the engine's behaviour during shifts.
Tuned cars with large turbos may work better with less reduction compared to cars with stock turbos. If you experience a bit of "lag" on a particular shift, you can also try lowering the torque reduction by a few percentage points until it smooths out.

Simply minimising all values won't do the trick, as lowering the amount of torque pulled during a shift will put more strain on your clutches and extend the shift time a little.

The 8HP transmission supports two shift modes (Soft and Hard), which can be combined with any driving mode (Comfort, Sport, Sport+). Stage 2 and 3 maps use both modes, while stage 1 retains the factory settings. Whether a car uses only the soft mode or both modes from the factory varies from model to model.
xHP mostly uses:

• “Comfort” uses soft shifts

• “Sport” uses both soft and hard shifts

• “Sport+” uses fast & hard shifts.

While this is a technical necessity in Sport+, the user is free to switch off the hard shifts in Sport.
The difference can easily be felt by the driver, as the hard shifts cause noticeable 'shocks' in the car's structure with every gear change. This is completely normal and does not damage the transmission or the car.

ZF has developed these modes, and OEMs use both modes as a marketing tool to differentiate between comfortable and sporty cars in their product range.

True manual means that when you're in manual mode, the car won't upshift by itself when the engine reaches the redline. Instead, it will hit the rev limiter like a car with a manual transmission.
The rev limiter will still protect the engine from over-revving.

Usually, this behaviour is desired for drifting or track racing. Depending on your car, this panel allows you to activate/deactivate True Manual for certain modes or generally switch it on/off. This depends on how the factory calibration is structured and differs for 8-speed, 7-speed and M cars.

The 6- and 8-speed automatic transmissions have three different shift speeds (Standard, Medium, Fast), which the TCU selects during driving based on several parameters.

For example, when the sport button is active, when the car is in manual mode or when the driver presses the accelerator quickly. Sometimes, the shift speed can also be limited generally, for example, when towing a trailer or during cold running.

The shift programs can be reassigned to this panel. For example, you can set the "Fast" program always to be active.
(= set “Standard” and “Medium” to “Fast”)

Or you can set the "Medium" shift program as the minimum available speed.
(= set “Standard” to “Medium”)

8-speed transmissions can cut off operation on one or more cylinders during shifting. This leads to faster shifting at the expense of smoothness and creates a distinctive exhaust note during shifts (braaap).
With this setting, you can configure the RPM and torque thresholds for each shift mode (Standard, Medium, Fast), at which point the transmission requests for cylinders to be cut off during shifts.

For example, when setting the “Standard” mode to 300 Nm and 4000 RPM, the transmission will request an Ignition-Cut shift when the current torque is above 300 Nm and the current engine speed is above 4000 RPM. “Standard” shift speed is usually used in “Comfort” or “Eco mode”, while “Medium” and “Fast” modes are selected depending on factors like DSC mode, “Sport” button state, throttle position and more.

This option only applies to gasoline engines.

This custom feature allows you to configure whether the transmission switches to S-mode or directly to M-mode when you tilt the automatic transmission lever to the left.

Allows the user to enable/disable the use of the kick-down switch.
There are two settings, Enabled and Disabled, which override the default settings in the map.

Throttle blips are used to adjust the engine speed during downshifts. This function allows you to set the aggressiveness of your downshift blips in manual and S-Mode.
The main aim of rev-matching is to speed up downshifts by actively matching the engine rpm to the target rpm in the target gear. This is achieved by applying a short blip to the throttle during the transition between 2 gears.
Users can change the intensity of this blip by +-50% compared to the setting in any of the OTS maps or custom maps used.
Higher values result in more audible and faster blips but can be uncomfortable.
Lower values will result in slower but smoother rev-matching.

Lend your high-performance vehicle safely to your children, or ensure the garage mechanic does not show off your car to his mates. Valet Mode can be applied to any map and works safely in all driving environments.

• Limits your vehicle's power to approximately 100 hp in lower gears and 130 hp in higher gears.

• Limits max. RPM to approx. 2500-3000 (depending on vehicle)

• Disables kick down

• Prevents premature downshifting in manual mode (max. 2500 rpm)

• Locks the transmission in its slowest operating mode

• Disables launch control/brake boost.

Allows users to set their own WOT (Wide Open/Full Throttle) shift points. "Max RPM can be set separately for D-, S- and M-modes.

Allows the user to customise the display of the “current gear” on the instrument panel.
You can choose between Gear Display ON or OFF.

• “Default” uses whatever is set up in the flashed Map.

• “OFF” turns the Display off. The Dash will show just the current mode but not the current gear (except in M-Mode).

• “ON” will show the current gear in all modes (D, S and M).

Back to the Overview Page.