How to convert your BMW with N52 engine from a GM to a ZF 6HP transmission!
Contents
This guide covers everything you need to know to swap your BMW with N52 engine from GM to a ZF6HP transmission! It will not cover the general tasks how to remove your transmission from your car (which any mechanic can do) but the specifics you need to know for this particular swap.
History
Thanks to various circumstances, BMW had to fit a certain amount of vehicles in the period from roughly 2006 - 2010 with a 6-Speed GM Automatic Transmission, instead of the 6-Speed unit from ZF. Usually all BMW with 6-Speed Auto were fitted with either the ZF 6HP19/21, ZF 6HP26/28 or ZF 6HP32/34. However, BMW with N52 (and N43) engines were sometimes equipped with the GM unit. Most commonly the GM unit is found in the US-Versions of 325i and 330i (E9x) and the 125i/130i. (E8x)
Do I have a GM or ZF in my N52 BMW?
Online part-catalogs aren't able to determine whether a certain N52 vehicle at a certain build date got fitted with a GM or ZF unit. (Hint: your BMW Dealer can, based on your VIN. xHP will also tell you "not supported" when a GM trans is in your car) This creates constant confusion among potential xHP customers, whether they can use xHP or not. (xHP only works for ZF) While it is out of scope for us, to redo our development for the few cars with GM unit, it's pretty easy to swap your GM unit for a ZF and take advantage of an immense performance and fun gain. We're not shy to say, you won't recognize your car again. Some might disagree, but even if not "xHP-ed" the ZF is superior to the GM in many aspects and despite there are some traps, it's easy to swap when being prepared with the right parts and knowledge.
First of all, the correct ZF is a direct swap in any BMW with GM 6L45. It will bolt on the engine side and it will bolt to your driveline. As both transmissions were used in production and OEM's always tend to do as little variants of certain parts as possible, this isn't surprising at all. However, some auxiliary things need to be changed and you need to make sure to source the right ZF transmission, which is where your journey should start. We did this swap on a 2009 130i (LCI), so the transmission to source was a 6HP21, sometimes called 6HPTU. TU stands for "Technische Uberarbeitung" and is kind of the LCI version of the 6HP. (Note: the parts cataloge ALWAYS spits out "6HP19Z", regardless if the car in question has a 6HP19 or 6HP21. BMW just discriminiates them by PartNo.)
However, you need to make sure your are getting a ZF that matches your car and has the correct TCU fitted. The safest way of course is to source a ZF trans that comes from the very same car and build date, but this isn't mandatory and sometimes not even possible when only GM was used in that period. The 6HP came in 3 sizes and all cars that came with the GM 6L45 need a 6HP19 or 6HP21 for swapping. You can cancel out all other versions. As a rule of thumb search for a 6HP19 if your car is 2006 and before, all others are fine with a 6HP21. NOTE: Although TCU's from non-LCI cars can work in LCI vehicles, you may run into problems. (this depends on the program variant used in the DME and TCU and even may stop to work after updating one of them, so don't do it).
How do I find the correct ZF for swapping?
It's pretty easy to tell if you're looking at a 6HP19 or 21, cause it's stamped in the housing on the driver-side. But there's more to consider. There are many different program numbers out there and not all of them will work in your N52 car. The program number can be found on a white sticker, at the driver-side of the transmission and is preceeded by "HW".
For 2005/2006 N52 cars, those are safe to use:
HW#7563275
HW#7564645
Do NOT use transmissions from X3 E83 or Z4 E85/E86 in your E87/E88 or E9x car. Those communicate on K-Line and you won't be able to reach them through the OBD port. They would need to be bench-flashed before they are able to communicate in their new environment.
For cars 2007 and above, those are safe to use:
HW#7573661
HW#7591971
Both lists are not complete, but other HW# may have issues communicating and would need to be flashed before even P/R/N/D shifting is possible.
What other parts do I need for the swap?
Trans-Support-Bracket: 22326795972
Oil-Cooler Line Feed: 17227577635 (for E87 130i, check parts catalog for your car)
Oil-Cooler Line Drain: 17227577636 (for E87 130i, check parts catalog for your car)
If you sourced a trans from a 135i/335i you will need to swap the output flange to # 24207552327 as well. (those 6HP21s had bigger flanges compared to the smaller models)
Wiring
Although the connector on the vehicle loom to the trans is mechanically the same, the pin-out is totally different! Do NOT just plug the new trans in. You will need to open the connector, extract the pins (best to get a tool for that, otherwise it's major PITA. For instance Beta Set 1497/C23) and re-pin as shown below. It's pretty straight forward, if you mark all wires prior removing from the connector. Unused wires can be isolated and tucked away in the loom. (ZF has only one permanent positive, whereas GM had 2) Be sure not to mix the wires, as this can lead to permanent damage on the TCU. The picture shows the pin-out on the transmission! (mirrored to connector!) Double and Triple-Check for the right slot on the connector each time you place a wire! The connector usually has the Pin# stamped in, so you can compare it to the pin-out given below.
Getting it to work
Once the transmission is in place and wired, you can check for communication with xHP. It should instantly recognize your car now. If not, you likely have an issue with the wiring!
At this point you also may open the oil-filler screw slightly and check if there's even any fluid in there. Often used transmissions are emptied at the scrapyard, so you need to fill them up. Even if not, it's likely a good idea to do a service when you're already on it. (new oil, sealings and filter) Beware when checking oil, it will instantly spill, if you open too wide!
Start the car and check if PRND at the gear lever is working. If not, you likely have an issue in your wiring.
If all is fine, check oil-level with engine running according to ZF spec prior to driving.
Do a short test-drive, see if shifts are reasonably fine. Check if trans reacts to S-Mode at lever and +/- Steptronic. Check your steering wheel paddles in S.
If you got this far, you can use xHP just like anybody else. Have fun! If you still run into issues, or the app still tells you that you car is not supported, please contact us.
Disclaimer
This guide was written to the best of our knowledge but it is still your responsibility to double-check things (e.g. get electrical wiring plans from your very car!) and use common sense when carrying out this swap. We do not take any responsibility for damage caused on your car or the environment due to errors in the guide, installation errors or non-matching parts.
Back to the Overview Page.