About the

Flash Settings

Flash Settings offer many functions to tweak your transmissions behavior change the transmission's behaviour to your liking! All functions work on with your stock calibration, as well as on factory calibration and our OTS Mapsmaps! You are free to change Shiftpoints can change the shift maps for D- and S-mode, adjust Shift-Speeds the shift speeds or firmness for each shift (where available) or even adjust the Launch Control function of your vehicle! With our Import/Export feature you your car's launch control! You can also share your settings on Social Media social media or Import import settings from other users with our import/export feature!

The Custom. Module offers 2 Flash Settings offer two types of functions: Absolute or and relative.
Absolute functions are those where you set a fixed parameter , which then will be applied to every each flashed file flashed. For instance example, you could set a Torque Limiter torque limit of 500 Nm in 1st Geargear. This limiter will then be applied to every Map map you flash, wether whether it is your stock factory calibration, an OTS Maps map or a self-built custom file you have created. Every map will have apply this limiter applied, no matter regardless of what value was written in the Base-Filebase file.

Relative functions work slightly differentdifferently, as you can apply a delta to the flashed Mapmap. The Shiftmap Editor is such a relative function , where xHP will readout reads the respective corresponding values from every Map each flashed map and change changes them according to your settings. This makes it easy to adjust complex things like Shiftpointsshift maps.
Instead of having to worry worrying about what absolute value to set for a given shift (e.g. 1-2 in D-Modemode) , at a given Throttlethrottle/RPM position, you just apply a percentage delta in percent to the base settings already stored in the Mapmap. Every

Each relative function is configured through easy Sliders, which using simple sliders that allow you to set a positive or negative percentage for a given parameter. For instanceexample, if you want your 2-3 shift to happen occur earlier, you just set a negative Value (for instance: -value (e.g., 15%) for this that shift, and xHP will apply -15% to the complete entire map for the 2-3 shift.

This is always happens done within certain boundaries and will be auto-adjusted, so limits and is automatically adjusted so that the actual values applied to the Map map still make sense. The same principle applies to all functions , where you are able to can set a positive or negative percentage in xHP.

This chapter will explain every custom function available, separate explains each “flash setting” available separately for 6-Speedspeed, 7-Speed speed E-Series, 7-Speed speed F-Series or 8-Speed Transmissionsspeed transmissions! Most functions are available for all models, however but some functions may not be possible on available for certain vehicles cars due to technical restrictions. The Custom Module will show such functions greyed out.

.

Import/Export Function

By You can quickly export your current custom settings by pressing the "3-three white - dots" in the upper-top right corner of the Customization Module you can quickly export your currents custom settingsCustomisation module. The settings can either be stored saved in a file on your phone in a small file, or they can be forwarded to any Social Media Channel your device is offering (e.g. WhatsApp). or shared with other xHP users.
You can also easily import the settings from of any other xHP -User within seconds to user into your car . Compatibilty is limited in seconds.

Compatibility between transmission types is limited. 6-Speed Settings speed settings can only be imported to other 6-speed cars, 8-Speed speed to 8-Speed speed and 7-Speed speed to 7-Speedspeed.

Some settings of from 7-Speed speed F-Series series cars are not compatible to incompatible with 7-Speed speed E-Series and are therefore voided, yet the import in general will series cars and will be invalid, but the import will generally still work.

Please bear in mind, note that the customization Customisation module has many "relative" Settings. (e.g. Shiftpoints) This means it will make little sense to import Shift-Point settings. For example, importing shift map settings from a 550i to a 320d makes little sense. The app application will still change the maps in the 320d accordingly, but those these will of course not lead to result in the same shiftpoints shift maps as in the 550i.

The individual

Flash Settings for 6HP / 7-DCT / 8HP cars

For more detailed information on the individual custom modules options supported by your specific transmission type supports, please follow these links:

• 6-Speed ZF - Custom OptionsFlash Settings

• 7-Speed DCT - Custom OptionsFlash Settings

• 8-Speed ZF - Custom OptionsFlash Settings

Back to the Overview Page.