How to connect to your car

Once you have downloaded xHP on to your Android/iOS or Windows 10 Apple Silicon Mac (M1 processor and later) device and have acquired purchased the additional hardware needed required (see supported flashing hardware), you are ready to connect to your vehicle. This chapter will guide you through the steps needed ANY TIME you need to take before attempting to read or flash your vehicle.

Preparing your device

Preparing your vehicle

Connection via DCAN

cable (E, F & G

series)

• Plug in your cable to the OBD port of your vehicle. The OBD port is located in the drivers driver's footwell on the left side in LHD cars and on the right in RHD cars.

• Connect the OBD/DCAN cable with your USB OTG Adapter.

• Unlock your Android device.

• Connect the USB/OTG adapter to your Android device and wait for the USB permission screen to pop up. Please make sure that ensure you’re granting permanent access rights to xHP in on this screen. On some Android versions, the screen will only appear after the startup of xHP. Wait a few seconds after connecting the USB OTG cable.

• Start xHP, and after creating an account and logging in, hit the “Connect” Button.

Connection via DCAN Wi-Fi adapters (THOR, MHD, xHP)
(E, F

, G - Series & Supra)

Most Android devices will prefer Wi-Fi connections over to 4G/LTE. As soon as Once you connect to the Wi-Fi network created by the Thor, MHD or MHD xHP Wi-Fi Adapteradapter, you will can no longer be able to access the internetInternet, even if the cellular network is still turned onactive.
Therefore, the initial vehicle unlock unlocking the car for the first time requires a special procedure when using the Thor or orange MHD Wi-Fi Adapteradapter:

• Very first start: Start with an active Internet connection, so i.e. not connected to the wireless Adapter Wi-Fi wireless adapter. This is only true for applies to the very first startup. Not needed afterwards.Plug in your first start and is not required for subsequent flashes.

• Connect the Wi-Fi Adapter into adapter to the OBD port and wait 10-20 seconds. Connect to the created Wi-Fi on your device. Press the “Connect” button in the Appapp.
  The App app will pull retrieve the necessary data from your car , to perform the Online Support-Checkonline support check.

• Disconnect from the Adapter adapter Wi-Fi. You can now perform the Online - Support - Check and redeem your previously purchased voucher codes. (Codes can be bought at our Web-Shop)Afterwards you can switch The codes can be purchased from our https://www.xautomotive.com/ )

• You can then switch back to the Adapter Wi-Fi again. The app application has downloaded all necessary data and is now ready for offline use.

Setup requirements on iOS

Connection via ENET cable connection (F & G series)

For Windows devices, no additional configuration is required.
Just connect the ENET cable to your device.

If you still experience problems, please check that the automatically set IP address is within the range 169.254.x.x and that network services such as VPN, virtual network adapters and/or firewalls are not interfering.

If you experience connection problems, please disable these services. If your IP is not in the expected range, you can try to configure it manually, as explained below.

Android, iOS and MacOS users must configure the Ethernet port , after connecting the ENET Adapter adapter to their devices. Please open the settings panel on your device.
Depending on your Android version, the procedure may be a bit slightly different. The screens were screenshots are taken from a Galaxy S9 phone , running Android 9. This procedure is only necessary on first

You only need to do this the first time you connect. Your phone will store those remember these settings for subsequent connects. Eventually you need to re-plug the adapter, connections. In some circumstances, you may need to reconnect the adapter after saving the settings for them to take effect.

Setup requirements on Android

Make sure you have the latest Android updates installed. To connect to your car using a wired Ethernet connection, you must enable Ethernet Tethering - a new option introduced in Android 11. To enable Ethernet Tethering, please follow these steps

• Connect your ENET cable to your Android device (use a suitable adapter)

• Go to Settings → Connections → Mobile Hotspot and Tethering → Enable Ethernet Tethering.

On Android, you need to configure a static IP address:

Setup requirements on iOS

Setup requirements on Mac OS (M1 Macs and later only)

On Apple silicon Macs, you have to configure your IP address as well:

Connection via ENET Wi-Fi adapters (F & G series)

xHP also supports the new ENET wireless adapter from MHD. Just plug in MHD's ENET Wi-Fi adapter. Plug the adapter into your OBD port and connect to the created Wi-Fi named “MHD_xxxx” Fi called "MHD_xxxx" with the password “"MHD_ENET”. ".

Other suppliers might use the same adapters with different names and passwords.

No further configuration neededis required. The Adapter adapter works on with Apple and Android devicesAndroid devices. ENET is only available on for F and G -Series series vehicles. There is no support for E series vehicles with this adapter.
You can only flash G-Series cars with this adapterafter their transmissions have been successfully unlocked. See the yellow info-bubble below.

Most Android devices will prefer Wi-Fi connections over to 4G/LTE. As soon as Once you connect to the Wi-Fi network created by the MHD ENET - Wi-Fi Adapteradapter, you will no longer be able to access the internetInternet, even if the cellular network is still turned onactive. Therefore, the initial vehicle unlock unlocking of the car requires a special procedure when using the Thor or orange MHD an ENET Wi-Fi Adapteradapter:

• Very first start: Start with an active Internet connection, so i.e. not connected to the wireless Adapter Wi-Fi wireless adapter. This is only true for applies to the very first startupstart. Not needed afterwardsrequired for subsequent flashes.

• Plug in your Connect the Wi-Fi Adapter into adapter to the OBD port and wait 10-20 seconds. Connect to the created Wi-Fi on your device. Press Connect in the Appapp.
  The App app will pull retrieve the necessary data from your car , to perform the Online Support-Checkonline support check.

• Disconnect from the Adapter adapter Wi-Fi. You can now perform the Online - Support - Check and redeem your previously purchased voucher codes. (Codes can be bought at our Web-Shoppurchased from our webshop)

• Afterwards you You can then switch back to the Adapter Wi-Fi again. The app application has downloaded all necessary data and is now ready for offline use.

Setup requirements on iOS

Connection via MHD UNI Wi-Fi adapter (E, F & G series)

xHP also supports the MHD UNI Wi-Fi adapter. Plug the adapter into your OBD port and connect to the correct Wi-Fi. Based on the detected protocol, the Wi-Fi SSID will be one of the following

• MHD ENET XXXX

• MHD CAN XXXX

No further configuration is required. The adapter will work with all listed devices.

The MHD UNI Wi-Fi adapter supports E, F and G series cars, including Supras.

Most Android devices prefer Wi-Fi connections to 4G/LTE. Once you connect to the Wi-Fi network created by the MHD UNI Wi-Fi adapter, you will no longer be able to access the Internet, even if the mobile phone is still switched on. Therefore, a special procedure is required to unlock the vehicle for the first time:

• First start: Start with an active Internet connection, i.e. not connected to the Wi-Fi wireless adapter. This only applies to the very first start. Not required for subsequent flashes.

• Connect the Wi-Fi adapter to the OBD port and wait 10-20 seconds. Connect to the created Wi-Fi on your device. Press Connect in the app.
  The app will retrieve the necessary data from your car to perform the online support check.

• Disconnect from the adapter Wi-Fi. You can now perform the Online Support Check and redeem your previously purchased voucher codes. (Codes can be purchased from our https://www.xautomotive.com/)

• You can then switch back to the Adapter Wi-Fi. The application has downloaded all necessary data and is now ready for offline use.

Back to the Overview Page.